|Application||WB, IHC, IF,ELISA|
|Storage buffer||10 mM sodium HEPES (pH 7.5), 150 mM NaCl, 100 µg/ml BSA, 50% glycerol and less than 0.02% sodium azide.|
|Storage||Store at –20°C.|
1. Aspirate media from cultures and Wash the cells with 1X PBS. 2. Lyse cells by adding 1X SDS sample buffer and transfer the extract to a microcentrifuge tube. Keep onice. 3. Sonicate for 10–15 sec to complete cell lysis and shear DNA. 4. Heat a 20 µl sample to 95–100°C for 5 min, then cool on ice. 5. Centrifuge for 5 min (with Microcentrifuge). 6. Load appropriate volumes of samples onto SDS-PAGE gel (loading quantity of protein sample depends on the concentration of extracted proteins). NOTE: At the same time, please load the pre-stained molecular weight markers to determine molecular weights and verify electrotransfer. 7. Electrotransfer to nitrocellulose/PVDF membrane.
Membrane Blocking and Antibody Incubations
1. (Optional) After transfer, wash the transferred membrane with TBS for 5 min at room temperature. 2. Incubate the membrane in the blocking buffer for 1 hr at room temperature. 3. Wash three times for 5 min each with TBST.
b. Antibodies Incubation
1. Incubate membrane and primary antibody (at the appropriate dilution and diluent recommended) in a primary antibody dilution buffer with gentle agitation overnight at 4°C. 2. Wash three times for 5 min each with TBST. 3. Incubate membrane with an appropriate second antibodydissolved in the blocking buffer with gentle agitation for 1 hr at room temperature. 4. Wash three times for 5 min each with TBST. 5. Proceed with detection.
Detection of Proteins
1. After antibodies incubation, Wash membrane three times for 5 minutes in TBST. 2. PrepareECL Reagent (or other chromogenic agents/substrate according to your second antibody). Mix well. 3. Incubate substrate with membrane for 1 minute, remove excess solution (membrane remains wet), wrap in plastic and expose to X-ray film.
NOTE: Do not allow slides to dry at any time during this procedure.
1. Deparaffinize/hydrate sections:
1. Incubate sections in three washes of xylene for 5 min each.
2. Wash sections two times in dH2O for 5 min each.
For Citrate: Heat slides in a microwave submersed in 1X citrate unmasking solution until boiling is initiated; continue with 10 min at a sub-boiling temperature (95°-98°C). Cool slides on bench top for 30 min.
1. Wash sections in dH2O three times for 5 min each.
Specimen Preparation (forcultured cell lines, IF-IC)
1. Aspirate liquid, then cover cells to a depth of 2–3 mm with 4% formaldehyde diluted in 1X PBS.
1. Add theblocking buffer and incubate for 60 min at RT.
|Specificity||SP1 Rabbit Recombinant mAb detects endogenous level of SP1.|
|Background||Sp1 is a ubiquitously expressed, prototypic C2H2-type zinc finger-containing DNA binding protein that can activate or repress transcription in response to physiologic and pathological stimuli. Sp1 can be phosphorylated by many kinases in addition to DNA-PK and that phosphorylation can also be affected by protein phosphatases. Phosphorylation occurs at various locations in Sp1, including the C-terminus, and often results in functional changes to Sp1 such as altered DNA binding and/or promoter activation. Sp1 phosphorylation is increased along with organ development and maturation in the liver and lung. The less phosphorylated Sp1 is associated with rapid growth.|