|Application||WB, IHC, IF,ELISA|
|Storage buffer||10 mM sodium HEPES (pH 7.5), 150 mM NaCl, 100 µg/ml BSA, 50% glycerol and less than 0.02% sodium azide.|
|Storage||Store at –20°C.|
1. Aspirate media from cultures and Wash the cells with 1X PBS. 2. Lyse cells by adding 1X SDS sample buffer and transfer the extract to a microcentrifuge tube. Keep onice. 3. Sonicate for 10–15 sec to complete cell lysis and shear DNA. 4. Heat a 20 µl sample to 95–100°C for 5 min, then cool on ice. 5. Centrifuge for 5 min (with Microcentrifuge). 6. Load appropriate volumes of samples onto SDS-PAGE gel (loading quantity of protein sample depends on the concentration of extracted proteins). NOTE: At the same time, please load the pre-stained molecular weight markers to determine molecular weights and verify electrotransfer. 7. Electrotransfer to nitrocellulose/PVDF membrane.
Membrane Blocking and Antibody Incubations
1. (Optional) After transfer, wash the transferred membrane with TBS for 5 min at room temperature. 2. Incubate the membrane in the blocking buffer for 1 hr at room temperature. 3. Wash three times for 5 min each with TBST.
b. Antibodies Incubation
1. Incubate membrane and primary antibody (at the appropriate dilution and diluent recommended) in a primary antibody dilution buffer with gentle agitation overnight at 4°C. 2. Wash three times for 5 min each with TBST. 3. Incubate membrane with an appropriate second antibodydissolved in the blocking buffer with gentle agitation for 1 hr at room temperature. 4. Wash three times for 5 min each with TBST. 5. Proceed with detection.
Detection of Proteins
1. After antibodies incubation, Wash membrane three times for 5 minutes in TBST. 2. PrepareECL Reagent (or other chromogenic agents/substrate according to your second antibody). Mix well. 3. Incubate substrate with membrane for 1 minute, remove excess solution (membrane remains wet), wrap in plastic and expose to X-ray film.
NOTE: Do not allow slides to dry at any time during this procedure.
1. Deparaffinize/hydrate sections:
1. Incubate sections in three washes of xylene for 5 min each.
2. Wash sections two times in dH2O for 5 min each.
For Citrate: Heat slides in a microwave submersed in 1X citrate unmasking solution until boiling is initiated; continue with 10 min at a sub-boiling temperature (95°-98°C). Cool slides on bench top for 30 min.
1. Wash sections in dH2O three times for 5 min each.
Specimen Preparation (forcultured cell lines, IF-IC)
1. Aspirate liquid, then cover cells to a depth of 2–3 mm with 4% formaldehyde diluted in 1X PBS.
1. Add theblocking buffer and incubate for 60 min at RT.
|Specificity||RelB Rabbit Recombinant mAb detects endogenous level of total RelB.|
|Background||RelB is a member of the NF-κB family of transcription factors (RelA, c-Rel, NF-κB1 and NF-κB2) which is structurally and functionally different from the other two transcriptionally active members, RelA and c-Rel. RelB expression, contrary to that of RelA, is mainly restricted to lymphoid organs, namely the thymus (thymic medulla), spleen, and lymph nodes (deep cortex). RelB, together with p50 and c-Rel, is a major contributor to the constitutive nuclear NF-κB activity observed in lymphoid organs, within mature B cells, plasma cells and interdigitating dendritic cells. The c-myb enhancer promoter region is transactivated by RelB, but not RelA, via specific κB sites. An additional major difference between RelB and RelA is their regulation by cytosolic inhibitor proteins. While RelA is sequestered in the cytosol by IκB proteins such as IκBα,β, or ε which are targeted by post-translational modifications, RelB is not susceptible to their cytosolic inhibition. RelB transcription is RelA-dependent. They directly and independently regulate RelB promoter gene transcription|