|Reactivity||Human Mouse Rat|
|Storage buffer||10 mM sodium HEPES (pH 7.5), 150 mM NaCl, 100 µg/ml BSA, 50% glycerol and less than 0.02% sodium azide.|
|Storage||Store at –20°C.|
1. Aspirate media from cultures and Wash the cells with 1X PBS. 2. Lyse cells by adding 1X SDS sample buffer and transfer the extract to a microcentrifuge tube. Keep onice. 3. Sonicate for 10–15 sec to complete cell lysis and shear DNA. 4. Heat a 20 µl sample to 95–100°C for 5 min, then cool on ice. 5. Centrifuge for 5 min (with Microcentrifuge). 6. Load appropriate volumes of samples onto SDS-PAGE gel (loading quantity of protein sample depends on the concentration of extracted proteins). NOTE: At the same time, please load the pre-stained molecular weight markers to determine molecular weights and verify electrotransfer. 7. Electrotransfer to nitrocellulose/PVDF membrane.
Membrane Blocking and Antibody Incubations
1. (Optional) After transfer, wash the transferred membrane with TBS for 5 min at room temperature. 2. Incubate the membrane in the blocking buffer for 1 hr at room temperature. 3. Wash three times for 5 min each with TBST.
b. Antibodies Incubation
1. Incubate membrane and primary antibody (at the appropriate dilution and diluent recommended) in a primary antibody dilution buffer with gentle agitation overnight at 4°C. 2. Wash three times for 5 min each with TBST. 3. Incubate membrane with an appropriate second antibodydissolved in the blocking buffer with gentle agitation for 1 hr at room temperature. 4. Wash three times for 5 min each with TBST. 5. Proceed with detection.
Detection of Proteins
1. After antibodies incubation, Wash membrane three times for 5 minutes in TBST. 2. PrepareECL Reagent (or other chromogenic agents/substrate according to your second antibody). Mix well. 3. Incubate substrate with membrane for 1 minute, remove excess solution (membrane remains wet), wrap in plastic and expose to X-ray film.
NOTE: Do not allow slides to dry at any time during this procedure.
1. Deparaffinize/hydrate sections:
1. Incubate sections in three washes of xylene for 5 min each.
2. Wash sections two times in dH2O for 5 min each.
For Citrate: Heat slides in a microwave submersed in 1X citrate unmasking solution until boiling is initiated; continue with 10 min at a sub-boiling temperature (95°-98°C). Cool slides on bench top for 30 min.
1. Wash sections in dH2O three times for 5 min each.
ERK2 Rabbit Recombinant mAb detects endogenous levels of total ERK2.
Extracellular signal-regulated kinases(ERK2), also called MAPK1, is one of subtypes of ERK. ERK is a serine/threonine kinase which acts as an essential component of the MAP kinase signal transduction pathway. MAPK1/ERK2 and MAPK3/ERK1 are the 2 MAPKs which play an important role in the MAPK/ERK cascade. They are phosphorylated by upstream kinases and transduce signals. ERK is an integration point for multiple biochemical signals, and are involved in a wide variety of cellular processes such as proliferation, differentiation, transcription regulation and development. Upon activation, this kinase translocates to the nucleus of the stimulated cells, where it phosphorylates nuclear targets. It has substantial numbers of substrates including transcription factors (such as ATF2, BCL6, ELK1, ERF, FOS, HSF4 or SPZ1), cytoskeletal elements (such as CANX, CTTN, GJA1, MAP2, MAPT, PXN, SORBS3 or STMN1), regulators of apoptosis (such as BAD, BTG2, CASP9, DAPK1, IER3, MCL1 or PPARG), regulators of translation (such as EIF4EBP1) and a variety of other signaling-related molecules (like ARHGEF2, DCC, FRS2 or GRB10), protein kinases (such as RAF1, RPS6KA1/RSK1, RPS6KA3/RSK2, RPS6KA2/RSK3, RPS6KA6/RSK4, SYK, MKNK1/MNK1, MKNK2/MNK2, RPS6KA5/MSK1, RPS6KA4/MSK2, MAPKAPK3 or MAPKAPK5) and phosphatases (such as DUSP1, DUSP4, DUSP6 or DUSP16).